A burst pipe is two jobs: a plumber fixes the pipe, and a restoration company handles the water. In the Houston area, the water side is extraction, opening walls where water ran down the cavity, and drying.
Freezes are uncommon here, which is one reason many homes have pipes in attics and exterior walls with little insulation.

Typical steps
- Shut off the main. Know where it is before you need it.
- Call a plumber. For the pipe itself.
- Extract and open up. Water removed; wet drywall and insulation cut out.
- Dry. Equipment runs until readings show dry.
Do
- Turn off the water heater if the main is off for long.
- Photograph the damage[FEMA].
Avoid
- Turning the water back on before the pipe is fixed.
- Using ceiling fixtures below a wet ceiling.
How restoration crews in Houston classify water
The IICRC splits water into three categories. Category 1 is clean water from a source like a burst supply line. Category 3 is grossly contaminated, and the IICRC lists sewage, waste line backflows from beyond a trap, seawater flooding, rising rivers or streams and contaminated wind-driven rain as examples[IICRC 2026 position statement]. Category 2 sits in the middle.
The category decides the order of work. Category 1 drying can start right away without contamination controls, while Category 2 and 3 losses get cleaned up under contamination controls before drying begins[IICRC 2026 position statement]. Rising creek and bayou water in Houston counts as Category 3, which is why flooded drywall and carpet usually come out instead of being dried in place.
A clean leak does not stay clean forever. Time and temperature can change the category[IICRC 2026 position statement], and Gulf Coast heat speeds that up.
Where water hides in Houston homes
On a slab foundation, which is common around Houston, water moves outward under walls and cabinets instead of draining down. A leak in a hall bath can show up as a damp closet two rooms away.
The AC system is easy to overlook. A clogged condensate line backs up the drain pan, and the EPA says pans that do not drain can let water into the HVAC system[EPA]. Keep the pan clean and the line flowing[EPA], especially when the unit is in the attic over finished rooms.
Places to check:
- Water heater pans and the floor around them
- Washer supply hoses and the wall behind them
- Sink cabinets and the subfloor under them
- Inside walls around pipes that leak or condense[EPA]
- Inside ductwork[EPA]
- Under flooring next to tubs, showers and toilets
Warning signs include a musty smell, swollen baseboards, peeling paint, flooring that lifts or cups, and a water bill that jumps with no change in use.
What can be saved and what usually goes
The deciding factors are the type of water and how long things stayed wet. Under the EPA flood guide, if something cannot be cleaned and made dry inside a day or two, it is discarded[EPA flood cleanup guide], and the CDC adds that items which cannot be disinfected, such as wall coverings, cloth, rugs and drywall, should be thrown away[CDC].
With clean water caught early, the EPA notes that wallboard, fiberglass insulation and wall-to-wall carpet may sometimes be dried and saved, though replacing them can avoid indoor air problems later[EPA flood cleanup guide].
Photograph everything before it goes to the curb[FEMA], and keep a list of what was removed.
Hurricanes, power outages and drying
Beryl came ashore near Matagorda on July 8, 2024 as a Category 1 hurricane with 80 mph winds, dropping around 4 to 8 inches of rain on average and 10 to 15 inches in some swaths[NWS]. CenterPoint’s tracker showed more than 2.2 million homes and businesses without power[Houston Public Media].
Drying equipment runs on power. When the grid is down, a soaked house sits in heat and humidity, so ask whether the restoration company can bring generator power for its equipment.
If you use a generator, keep it outdoors, at least 20 feet from doors, windows and vents, never in the garage, and run a battery carbon monoxide detector inside[CDC]. Carbon monoxide caused two indirect deaths after Beryl[NWS].
Freeze damage in Houston
Hard freezes are rare here, which is why they cause so much damage. In February 2021 the National Weather Service recorded 13°F in the city of Houston[NWS Houston/Galveston], and pipes in attics and exterior walls split across the region.
Leaks usually start when the ice melts, not while it is frozen. Find the main valve before cold weather arrives. A burst supply line is clean water at first[IICRC 2026 position statement], so the sooner it is extracted, the more drywall and flooring can be dried instead of removed.
Questions to ask the restoration company
- Which IICRC category does this water fall into?
- Can you show me the moisture readings and the wet area on a sketch?
- Which materials are coming out, and which can be dried in place?
- When will you take readings, and when do you expect the job to be dry?
- Do I need a plumber to stop the source first?
- Will you put the scope of work in writing before you start?
A good restoration company will answer these without hesitating and will take readings before giving a plan.
Where most household water damage starts
- Supply lines. Braided and plastic supply lines under sinks and toilets fail at the connection. A failed line can run at full pressure until the valve is closed.
- Water heaters. When the tank or fittings leak, water spreads across the slab from the garage, closet or utility room.
- Washers. Old rubber hoses split, and a washer drain that backs up puts dirty water on the floor.
- Air conditioning. Condensate lines clog and drain pans overflow, especially in long cooling seasons.
- Kitchen appliances. Ice maker lines and dishwasher hoses leak out of sight under the cabinets.
- Weather. Heavy rain, roof leaks and street flooding. Wind-driven rain that is contaminated counts as Category 3 water[IICRC 2026 position statement].
The source matters because it sets the water category and the starting point for moisture mapping.
What the restoration crew brings
- Pumps and extractors. Submersible pumps remove deep water. Extraction wands and weighted tools pull water out of carpet and pad.
- Air movers. Fans set at angles along walls and floors move air across wet materials.
- Dehumidifiers. Remove water from the air. Without them, air movers just push humid air around the room.
- Moisture meters. Measure the water in drywall, framing and subfloor, and confirm when each area is dry.
- Infrared cameras. Help locate wet areas behind finished surfaces, with meters used to confirm.
- Containment. Plastic sheeting closes off the work area, which keeps contaminated water and drying air where they belong.